DEI Boom Mat vs VEVOR 200 mil: Barrier or Foil Foam?

Design Engineering’s Boom Mat Leather Look 050120 and VEVOR’s 200 mil Noise Grabber are not interchangeable sound barriers. DEI’s manufacturer documents a dense 1 lb per sq ft loaded barrier, one 24 × 48-inch piece with an interior leather-like finish. VEVOR markets a 36 sq ft, 5.1 mm aluminum-foil/foam automotive insulation roll. A larger package does not make foam equivalent to a loaded sound barrier, and neither has a verified direct same-car laboratory comparison here.

Evidence scope: Manufacturer information from DEI and VEVOR, the original linked ASINs and both existing SPD reviews were considered. Manufacturer specifications are identified as such; conflicting retailer thickness fields, precise model variants and claims of heat/acoustic performance are not silently treated as test certificates. This is a buyer’s installation comparison, not a hands-on vehicle test.

Barrier mass and lightweight foam serve different acoustic roles

A dense loaded barrier is intended to make it harder for airborne noise to pass through a properly designed and fitted assembly. The density, coverage, edges and sealing method matter. A foil-faced foam layer is generally described for insulation, thermal reflection and decoupling or some absorption, depending on the foam and placement. Neither is identical to the thin butyl-constrained metal-damping sheets used to suppress sheet-metal ringing. Do not assume every material advertised as “soundproofing” blocks sound by the same mechanism.

DEI 050120: finished loaded barrier for selected interior areas

Existing SPD source-review image of DEI Boom Mat Leather Look 050120 black interior sound barrier
Existing image associated with DEI 050120; manufacturer confirms a finished black leather-look 8 sq ft sheet.

Design Engineering’s official product page identifies 050120 / 50120 as a single 24 × 48-inch (8 sq ft) leather-look sound barrier with a loaded core stated at 1 lb per sq ft. A 24 × 48 sheet calculates to 24 × 48 ÷ 144 = exactly 8 sq ft. The maker’s specification table says 3/8 inch thick. A retailer technical table states around 0.313 inch instead; another source calls it 5/16 inch. This is a material thickness discrepancy, not a basis to claim both exact figures true. Use the manufacturer 3/8-inch figure provisionally and check the delivered 050120 material where trim clearance is tight.

The black embossed surface is intended to be visible in some vehicle interiors, unlike hidden adhesive damping mats. DEI lists trunks, door panels, floor boards, speaker boxes and rear decks as examples. Its installation guide says the material can be trimmed with scissors and adhered using Hi-Temp Spray Adhesive 10492 if permanent fixing is desired. Gloves, eye protection, suitable ventilation and a paper template are recommended in the maker’s instructions. Unlike a self-adhesive sheet, this may require an additional bonding product and application step.

DEI marketing describes moisture resistance, temperature benefits and a premium appearance. We did not find a third-party comparative cabin-noise or thermal test for the exact Amazon purchase variant, and some retailers disagree on sheet thickness. Read the SPD DEI 050120 review or check the original DEI Amazon listing.

VEVOR Noise Grabber: 36 sq ft of 200 mil foil/foam

Existing SPD source-review image associated with VEVOR 200 mil aluminum foil foam Noise Grabber insulation mat
VEVOR 200 mil foil-and-foam review image; do not mistake it for the brand’s separate butyl rubber variants.

VEVOR’s current product page describes a 36 sq ft, 200 mil (5.1 mm) automotive insulation mat using an aluminum foil and foam construction, with a stated roll dimension of 16.5 × 315 inches. The dimension calculation 16.5 × 315 ÷ 144 ≈ 36.09 sq ft aligns with its rounded advertised area. VEVOR markets it as a thermal and acoustic insulation product, and offers other material variations including aluminum/foil/butyl options: check the material selector carefully before choosing.

Although some VEVOR descriptions contain “mass barrier” or “mass-loaded” language, the selected manufacturer material field says Aluminum Foil Foam. No 1 lb/sq ft loaded-vinyl layer or independently measured barrier transmission-loss value was established for this exact 200 mil configuration, so we do not present it as equivalent to DEI’s loaded barrier. The foil facing and thicker foam profile might be appropriate behind some vehicle trim, subject to permitted depth, adhesive compatibility and location-specific thermal requirements.

The original VEVOR affiliate B0CPY4GFKF remains unchanged. Its PADO monitor reports a stored active affiliate route, but the exact current checkout material selection on Amazon is not independently locked here. Read the SPD VEVOR review and check the original VEVOR linked offer.

At-a-glance buying comparison

Factor DEI Boom Mat 050120 VEVOR Noise Grabber 200 mil
Original ASIN B005Q585MO B0CPY4GFKF
Material role Loaded noise barrier with leather-look finish Foil-faced foam insulation/decoupling
Format One 24 × 48 in piece One 16.5 × 315 in roll, marketed size
Geometric area 8.00 sq ft ~36.09 sq ft
Nominal thickness Maker says 3/8 in; some sellers 5/16 in 200 mil / 5.1 mm
Fixing Optional permanent high-temp spray adhesive Self-adhesive installation as seller describes
Comparable independent isolation rating Not identified for this exact vehicle Not identified

VEVOR’s advertised nominal area is approximately 36 ÷ 8 = 4.5 times DEI’s material area; that says nothing about mass, sound transmission loss, thermal performance or delivered value. A 36 sq ft foam roll is not “4.5 times more soundproof” than an 8 sq ft loaded barrier. DEI’s stated loaded mass would be roughly eight pounds for an eight-square-foot layer on its quoted 1 lb/sq ft basis, before any other components; this is a supplier-based calculation, not a package weight measurement.

How to select the correct product

For a vehicle interior where a decorative dense loaded barrier is appropriate and safe to place, DEI’s finished 8 sq ft sheet is the relevant category. If the project calls for flexible foam/foil insulation across a larger interior area with enough clearance behind the trim, VEVOR’s 200 mil option is the better-formatted purchase category. Neither is an approved standalone answer to all road noise; an effective installation can require sealing air gaps, controlling panel vibration and fitting different barriers in separate layers.

Check trim depth, floor carpeting, service access and whether the chosen material can be safely used in the specified location. Any thermal/fire exposure should be assessed from the manufacturer’s material-specific documents, not product headlines.

Installation and safety checklist

  • Confirm DEI part 050120 or the exact VEVOR 36 sq ft foil/foam selected variant and supplied dimensions.
  • Template before cutting; measure real accessible panel areas and allow waste.
  • Clean and dry materials and substrates and address corrosion or leaks first.
  • When using DEI spray adhesive, follow DEI’s instructions and protect skin, eyes and ventilation.
  • Keep seatbelt mounts, airbags, door drains, controls and service panels functional.
  • Do not install near exhaust or heat sources without application-specific approval.

Frequently asked questions

Are these both mass-loaded vinyl?

No source evidence supports calling the 200 mil VEVOR foil/foam selected option a verified 1 lb/sq ft loaded barrier. DEI specifically states a loaded core.

Why do DEI retailer thicknesses vary?

DEI’s own page states 3/8 inch; another retailer lists about 0.313 inch. This source conflict remains disclosed.

Does a larger mat automatically stop more road noise?

No. Coverage, weight, installation seams and source noise paths differ; the 4.5× value compares nominal areas only.

Is the VEVOR foil foam the same as 80 mil butyl?

No. Those are separate material selections in the wider VEVOR catalog.

SPD’s decision

Choose by material function, not headline “soundproofing” terminology: DEI is the finished loaded-barrier approach for a selected small area, and VEVOR is a wider foil-foam insulation roll. Verify exact material, thickness and installation conditions before buying.

Affiliate disclosure: The original Amazon links are affiliate links. As an Amazon Associate I earn from qualifying purchases.

Good luck and happy soundproofing!