Affiliate disclosure: This article contains affiliate links. We may earn a commission if you purchase through them, at no additional cost to you.
Quick verdict: Second Skin Damplifier Pro and Noico Black 80-mil are both self-adhesive butyl-and-foil automotive vibration-damping sheets. The important difference in this comparison is the original Damplifier Pro eight-sheet door pack versus a separately identified Noico Black 36-sq-ft manufacturer format. They are not equivalent purchased packages, and no independent same-vehicle vibration or road-noise test is presented here.
Disclosure: As an Amazon Associate I earn from qualifying purchases. The original Damplifier Pro Amazon link below is tracked and may earn a commission. No verified original Noico Amazon destination exists in this article, so the Noico manufacturer specification is linked directly, without creating another affiliate route.
Start with the exact original products
The saved commercial link for this article is the Second Skin Damplifier Pro eight-sheet pack, original ASIN B0134VHSGK. An ASIN-associated retailer record describes eight 12 × 20-inch sheets marketed as 13.67 sq ft of 2 mm automotive butyl rubber mat. Second Skin’s own technical page gives 12 × 20-inch sheets, 2 mm (80-mil) overall thickness, black annealed foil and 0.70 lb/sq ft material weight.
There is a small coverage arithmetic discrepancy worth knowing before you buy: a 12 × 20-inch sheet has 240 square inches, or 1.667 sq ft; multiplied by eight, this is 13.33 sq ft. The ASIN-specific retailer description markets 13.67 sq ft and some sellers state 13.5. Do not assume that an advertising figure overrides the actual count and measured sheet geometry. Confirm the currently delivered contents and allow for overlaps and trimming.
The Noico comparison reference is the manufacturer’s Noico Black 80-mil DMM1 36-sq-ft kit, not an invented affiliate SKU. It uses nine folded foil-faced butyl sheets, each nominally 29.5 × 19.5 inches, marketed as 80 mil (2 mm). The manufacturer lists 0.7 lb/sq ft total material weight and recommends rolling down the embossed foil. A separate original SPD Noico sound-deadener overview discusses the broader line, whose size and color variants can differ.
What the materials look like


Both use a heavy viscoelastic butyl adhesive layer bonded to a metal constraining face. These materials are used on suitable vibrating vehicle panels so they deform less freely and radiate less panel noise. They do not seal a cabin against airborne road noise by themselves, and they are not substitutes for an under-carpet mass barrier, an appropriate acoustic foam spacer or correctly installed weather seals.
Damplifier Pro versus Noico Black 80 mil: specification table
| Decision | Second Skin Damplifier Pro | Noico Black 80 mil |
|---|---|---|
| Compared product identity | Original Amazon ASIN B0134VHSGK; eight-sheet pack | Manufacturer DMM1 black 36-sq-ft reference; untracked |
| Nominal thickness | 80 mil / 2 mm (maker specification) | 80 mil / 2 mm (maker specification) |
| Construction | Elastomeric butyl with black annealed foil | Butyl adhesive with embossed aluminum foil |
| Pieces and dimensions | 8 × 12 × 20 inches, per listed original kit | 9 folded × approximately 29.5 × 19.5 inches |
| Advertised coverage | 13.67 sq ft; sheet arithmetic gives about 13.33 sq ft | 36 sq ft |
| Maker-stated material mass | 0.70 lb per sq ft | 0.70 lb per sq ft |
| Manufacturer product ID | Damplifier Pro (not standard Damplifier) | Noico Black DMM1, not Red foam liner |
| Original tracked commercial route | One preserved original Amazon link | No original product-specific tracked link preserved |
| Measured noise improvement on the same vehicle | Not independently established | Not independently established |
Where each format makes sense
Choose the smaller original Damplifier Pro kit for a measured and relatively contained area, such as a limited door, trunk or panel-damping job, if you value Second Skin’s material specification and can verify the eight-sheet package. It is not necessarily enough to cover a whole vehicle. Second Skin publishes additional maker tests for its material, including heat aging and a vehicle flammability standard. Those are described performance and compliance claims for the material under the listed test method, not proof that every installation environment or near-engine location is approved.
Investigate the Noico Black 36-sq-ft format if the planned job requires more total sheet coverage and the larger pieces are practical to trim around vehicle structures. Its folded sheet format may be convenient across broad floor or roof panels but can need more cutting around door hardware. The manufacturer says its embossed face should be flattened with a hand roller. This is a manufacturer’s product reference, not a current affiliate offer or guarantee that the same package is in stock.
The Noico package advertises roughly 2.7 times the area of the Damplifier Pro eight-piece listing (36 divided by 13.33), but area ratio is not an acoustic performance ratio. An evenly installed material may still be ineffective if a vehicle’s dominant noise source is tire transmission, weather seals, airflow or a vibrating trim piece rather than a panel resonance.
Installation and safety checks
- Inspect and clean the application surface. Remove oil, rust, loose paint and moisture according to each maker’s instructions, then press the butyl into continuous contact with an approved roller.
- Check the local environmental and fire requirements for under-hood, firewall, floor and other sensitive surfaces. A general maker temperature claim is not permission to place an adhesive mat against hot exhaust or moving components.
- Protect water drains, window mechanisms, wiring, service fasteners, airbags, sensors and factory ventilation paths. Avoid using sheets where future repair access is essential.
- Use a budget measured in actual square footage, cut waste, added weight and labor. Larger sheets are not inherently better when every panel has openings to work around.
- Distinguish manufacturer’s lab reports, installation instructions and retailer advertising from real measured change in your vehicle; we have not carried out a direct vibration or decibel trial of either kit.
Buying decision and final verdict
The first question is the panel area and installation location; the second is which exact kit you can verify. Second Skin’s original product-linked route is preserved as Damplifier Pro B0134VHSGK, and readers can consult the existing SPD Damplifier Pro source review. For the other side, use the Noico manufacturer DMM1 documentation and the SPD Noico overview; there is no new Noico affiliate route here.
Decision: The smaller original Second Skin pack is more convenient for targeted treatment, while the manufacturer-identified Noico 36-sq-ft kit is a better coverage reference for larger jobs. Neither is proven to outperform the other acoustically without a matched, properly conducted installation test. Verify the actual selected pack, return conditions, and safe application locations before purchasing.
Good luck and happy soundproofing!