GOSCHE and X AUTOHAUX both sell foil-faced, nominally 10 mm automotive insulation products, but the linked packages cover very different areas. GOSCHE’s selected 15-sheet kit is advertised for about 16 square feet, while the X AUTOHAUX listing is for one sheet measuring approximately 2.16 square feet. The area difference matters far more to an installation plan than the shared “394 mil” headline.
Compare their actual functions
Both products are marketed for noise and heat control in vehicles. The available product records describe compressible foam layers with an aluminum-faced surface. That is different from a conventional thin butyl-constrained-layer damping sheet, which is installed directly onto vibrating metal panels to reduce their resonance. Foam-based liners can help separate surfaces and contribute to thermal treatment; their exact performance depends on the underlying metal, attachment and assembly. The source listings do not supply controlled head-to-head sound-transmission results for these linked products.
For a project that needs genuine metal-panel vibration damping, first decide whether a suitable butyl damper is required. A thick foil-faced foam product should not automatically be credited with the same function merely because its listing uses the words “sound deadening.”
GOSCHE 394 mil — the 15-piece package

The ASIN-specific GOSCHE record for B09MCSZ6G7 describes model GOSCHE-1122, nominal 394 mil or approximately 10 mm thickness, and 15 pieces measuring about 9.8 × 15.7 inches each. The advertised total coverage is 16 square feet. Multiplying the stated sheet dimensions gives roughly 16.0 square feet before trimming or overlapping; that is a package figure, not a promise of usable coverage on a complex door or firewall.
It is listed as a lightweight, closed-cell foam thermal/noise liner. The seller’s description suggests many automotive placement areas, but that broad marketing language is not an engineering approval for all high-heat locations. No verified fire classification, adhesive service-temperature chart or under-hood compatibility test was identified for this exact ASIN. Avoid contact with exhaust, turbochargers, hot manifolds and moving engine components without vehicle-specific manufacturer-approved clearances.
The GOSCHE package can be convenient for several small or medium interior areas where multiple sections are easier to fit than a large continuous sheet. The many seams may also mean more careful cutting and positioning. For context, read our GOSCHE overview or check the exact linked 15-piece GOSCHE kit.
X AUTOHAUX 394 mil — the single-sheet package

The matched retailer listing for B0DDKJH9VY describes one approximately 50 × 40 cm (19.69 × 15.75 in) sheet, 10 mm / 394 mil nominal thickness, with about 2.16 square feet of coverage. The listing mentions hood, fender and boat-engine-cover uses. Those uses reflect seller positioning, not independent confirmation of safe application on every hot engine cover or marine installation.
Choose a small sheet when you need to treat a bounded area, test the shape and thickness or avoid buying a large kit. However, a single piece is usually not enough for a vehicle floor or multiple doors. If buying several sheets, compare the total number of pieces and price based on actual square footage; do not compare one X AUTOHAUX unit with an entire 15-piece GOSCHE kit as though the package sizes were equivalent.
Our X AUTOHAUX review explains the stated use cases. The linked Amazon single-sheet option should be checked for dimensions, pack size and current directions before ordering.
Specification comparison
| Specification | GOSCHE B09MCSZ6G7 | X AUTOHAUX B0DDKJH9VY |
|---|---|---|
| Nominal thickness | 394 mil / 10 mm | 394 mil / 10 mm |
| Package format | 15 separate sheets | One sheet |
| Sheet dimensions | Approx. 9.8 × 15.7 in | Approx. 19.69 × 15.75 in (50 × 40 cm) |
| Advertised total area | 16 sq ft | 2.16 sq ft |
| Construction description | Compressible closed-cell foam with foil-facing marketing | Foil-faced insulating mat with foam layer |
| Typical buyer question | Will multiple pieces cover my proposed cabin area? | Will one sheet fit the small location I want to treat? |
| Verified standardized sound or fire test for this ASIN | Not identified | Not identified |
At the advertised figures, 16 divided by 2.16 is approximately 7.4. That is the nominal package-area ratio, not a claim that GOSCHE performs 7.4 times better acoustically. Thickness and area alone cannot establish acoustic effectiveness.
Installation questions to resolve first
- Surface and thickness: Clean and dry the proposed bonding surface. Confirm that 10 mm thickness will not interfere with trim clips, hoods, wiring, seals or moving components.
- Temperature and fire: A shiny foil face is not proof of an approved heat shield. Check the exact material’s adhesive temperature rating and the vehicle manufacturer’s clearances before any hot-zone use.
- Water and drainage: Do not obstruct door-drain holes or trap moisture in cavities. Seller water-resistant language does not by itself prove an installation is corrosion-safe.
- Metal vibration: If ringing sheet metal is the main problem, consider the role of a dedicated constrained-layer damping product before adding a foam liner.
- Handling: Measure the installation area, allow for trimming losses and use the application instructions from the exact delivered pack.
What the evidence does not establish
Neither source offers a controlled comparison of the two products in the same vehicle with the same mounting method. There is no defensible head-to-head cabin dB reduction figure, sound transmission class, noise reduction coefficient or quantified heat-flux comparison in the sources reviewed here. Seller phrases such as “2× more effective” should not be converted into measured performance without a published test method and full assembly conditions.
Frequently asked questions
Are these butyl sound-deadening mats?
The linked source descriptions emphasize thick compressible foam and foil-faced insulation. Do not assume that either works like a thin adhesive butyl sheet simply because the marketing copy includes “sound deadening.”
Can I put either one directly on a hot engine part?
No such blanket approval is supported. A retailer’s hood or engine-cover use suggestion does not replace a verified service-temperature rating or the vehicle’s safe installation requirements.
Why is the GOSCHE pack so much larger?
It contains 15 listed sheets rather than one. Compare total area and layout, not just nominal thickness or one-product price.
Does 394 mil mean high acoustic performance?
It indicates nominal physical thickness of approximately 10 mm. It is not a laboratory sound reduction rating.
SPD’s approach
For multiple interior sections, we would start by checking whether the larger GOSCHE pack covers the intended surfaces and whether the material’s temperature and attachment limits suit them. For one small insulated area, the single-sheet X AUTOHAUX format may avoid unnecessary waste. For a noisy resonating metal panel, we would first solve the damping requirement rather than treating two 10 mm foam listings as equivalent sound barriers.
Product documentation reviewed
GOSCHE B09MCSZ6G7 listing and package specifications; X AUTOHAUX B0DDKJH9VY ASIN-specific specification record. These establish package configurations and seller claims, not independent performance certification.
Affiliate disclosure: This page contains Amazon affiliate links. As an Amazon Associate I earn from qualifying purchases.
Good luck and happy soundproofing!