Affiliate disclosure: This article contains affiliate links. We may earn a commission if you purchase through them, at no additional cost to you.
Quick verdict: 60-mil Rockville versus 80-mil Kilmat
Rockville ROCKMAT 37-15 and Kilmat 80-mil 36-sq-ft mats are both marketed as self-adhesive butyl-and-aluminum materials for reducing vehicle-panel vibration. The specific Rockville offer contains fifteen 20 × 18-inch sheets, totalling 37.5 sq ft at 60 mil, plus an installation roller. Kilmat’s KLM8036 family pack contains thirty-four approximately 15.7 × 9.8-inch sheets, marketed as 36 sq ft at 80 mil, with no roller included. The useful choice depends on clearance, sheet geometry, project area and current offer — not a universal claim that thicker material performs 33% better.
Commercial limitation: The existing article has only one original tracked Amazon affiliate product, Rockville ASIN B0DWGWLSBM. Kilmat’s original source did not contain a verified Amazon affiliate key, and this comparison does not invent one. Kilmat is linked below to its official manufacturer product page as an untracked informational/buyer reference; no second PADO route, live Kilmat checkout or retail stock is certified.
Disclosure: As an Amazon Associate I earn from qualifying purchases. The Rockville link identified as sponsored may earn a commission at no extra cost. The Kilmat manufacturer source below is not presented as a tracked Amazon affiliate link.
Rockville ROCKMAT 37-15 — 60 mil, 37.5 sq ft

The Rockville direct product specification states 15 pre-cut 20 × 18-inch sheets, about 1.5 mm (60 mil) of butyl-and-reinforced-aluminum material, and an included wood-and-steel roller. A matching ASIN B0DWGWLSBM retailer record identifies the same ROCKMAT37-15 model and part family, although parts of the retailer’s structured “included components” text disagree with its own kit description. We therefore take the manufacturer’s package specifications as the product source and advise verifying shipment contents at purchase.
Material area is (15 × 20 × 18) ÷ 144 = 37.50 sq ft before offcuts. Flat rectangular sheets can cover larger exposed floor/trunk areas with fewer seams but need careful shaping inside tighter door internals. The manufacturer’s embossing/pressure indicator is an installation guide, not a verified comparative acoustic rating.
Read the Rockville ROCKMAT 37-15 product review. The existing tracked commercial destination is ROCKMAT 37-15 — original Amazon product route. Check the exact current pack, its 15-sheet configuration and included roller independently before ordering.
Kilmat 80 mil 36 sq ft — model KLM8036

Kilmat’s official KLM8036 page specifies 80 mil (about 2 mm), a 36-sq-ft marketed package, 34 individual sheets approximately 15.7 × 9.8 inches, and a butyl-and-aluminum self-adhesive construction. The manufacturer states no roller is included with this particular pack. Kilmat separately sells 50-mil, 80-mil and other area configurations; these should not be silently combined into a single composite specification.
Those listed sheets provide 34 × 15.7 × 9.8 ÷ 144 ≈ 36.32 sq ft of nominal rectangular face, close to the marketed 36 sq ft after rounding. The manufacturer’s claimed thickness-percentage benefits and acoustic descriptions are not an independently obtained matched-car or matched-panel loss-factor experiment.
The longstanding SPD Kilmat review surveys the family. For an exact 80-mil 36-sq-ft point of reference, Kilmat’s KLM8036 manufacturer product page is the appropriate untracked source, including its brand-presented purchase option. This is not a new tagged Amazon route and does not certify an Amazon partner commission, current selected marketplace offer or delivery.
Specification comparison
| Buyer factor | Rockville ROCKMAT 37-15 | Kilmat KLM8036 |
|---|---|---|
| Model | ROCKMAT 37-15 | KLM8036 |
| Nominal thickness | 60 mil (about 1.5 mm) | 80 mil (about 2 mm) |
| Marketed kit coverage | 37.5 sq ft | 36 sq ft |
| Sheet count and format | 15 × 20 × 18-inch sheets | 34 × 15.7 × 9.8-inch sheets |
| Materials | Butyl with reinforced aluminum | Butyl with aluminum facing |
| Roller in model documentation | Included | Not included |
| Original tracked affiliate route | ASIN B0DWGWLSBM, active saved PADO | None identified in this original comparison |
| Comparable instrumented acoustic test | Not obtained | Not obtained |
Kilmat’s nominal material thickness is 80 ÷ 60 ≈ 1.33 times Rockville’s, while the marketed package areas are similar: 37.5 ÷ 36 ≈ 1.04 times. The first ratio describes nominal thickness, and the second describes package area; neither predicts a 33% better sound result, a 4% improvement in damping or a universal winner.
What material does for a car
Constrained-layer damping products target vibration in suitable resonant vehicle metal panels. They are not substitutes for a complete airborne sound barrier, weather stripping or an acoustic absorber. A rattling door may benefit from treating the sheet metal, but a torn weather seal or worn wheel bearing needs a different remedy. Do not add weight blindly without diagnosing the noisy component.
Choose target areas, measure exposed metal rather than trim perimeter, and plan cutting waste. Clean and dry the intended surface, avoid oil and loose rust, adhere according to the maker’s temperature and surface instructions, and roll appropriately to establish contact. Preserve door water drainage, window channels, wiring, service openings, factory seals, airbag/seatbelt safety areas, electrical components and moving linkages. Never use an interior mat as an unverified direct catalytic-converter or exhaust heat shield.
When each product makes sense
Consider ROCKMAT 37-15 when you want a manufacturer-specified 15-sheet 60-mil kit with a listed installation roller and around 37.5 sq ft of material. The larger pieces can be convenient for broad surfaces; verify the actual item and any local freight/installation constraints.
Consider Kilmat KLM8036 when nominal 80-mil thickness and smaller sheet geometry fit your project, and the brand’s 34-sheet 36-sq-ft pack is specifically the product you wish to order. Its official product listing is a useful source, but the article does not possess a verified original Kilmat affiliate link.
Neither may be the best first step if your concern is an exterior-air leak, a faulty mechanical part, or a noise path primarily through an untreated opening. Panel vibration control is only one part of automotive noise treatment.
Frequently asked questions
Is Kilmat twice as thick as ROCKMAT 37-15?
No. The maker-listed values here are 80 versus 60 mil; the nominal thickness ratio is about 1.33, not two.
Do the two packs cover the same area?
They are close in marketed nominal coverage: Rockville 37.5 sq ft and Kilmat 36 sq ft. Different sheet dimensions create different cutting and handling conditions.
Does the thicker 80-mil sheet always damp more noise?
No. Damping efficiency depends on the material’s viscoelastic behavior, constraining layer, temperature, panel stiffness and application. These source pages do not establish a controlled same-car winner.
Is the Kilmat link an affiliate link?
No. The original article contains one active tracked Amazon route, for Rockville. Kilmat’s manufacturer page here is a direct, untracked product information and buyer reference. The missing Kilmat PADO commercial route remains an explicit gate hold.
Source and final recommendation
Product geometry and material roles are supported by Rockville’s manufacturer specifications, Kilmat’s KLM8036 maker details, the original linked Rockville retail ASIN source and the established SPD product reviews. Original Rockville Amazon tracking was retained, and no new Kilmat tagged ASIN or stock claim was manufactured.
SPD’s decision: base the choice on actual vehicle geometry, installation access, pack size, material thickness and the availability of suitable tools. ROCKMAT offers a 60-mil larger-sheet kit with a stated roller; Kilmat offers a 36-sq-ft 80-mil small-sheet pack when you select KLM8036. Neither has a verified general-purpose acoustic-performance advantage in a measured identical installation.
Good luck and happy soundproofing!