Affiliate disclosure: This article contains affiliate links. We may earn a commission if you purchase through them, at no additional cost to you.
Buyer verdict: two one-pound-per-square-foot barriers, different package sizes
Soundsulate Next Generation 1-lb Mass Loaded Vinyl and TotalMass 1-lb MLV are both dense, flexible membrane barriers intended to reduce airborne sound transmission when installed in a correctly designed wall, ceiling, floor or equipment assembly. The saved Soundsulate Amazon ASIN B0CN1G3C8Z is independently described as a 4 × 8-ft, 32-sq-ft sheet. TotalMass is available through its own distributor in multiple size options, including 4 × 10 ft (40 sq ft) and 4 × 25 ft (100 sq ft). Those different packaging choices, rather than an unverified decibel advantage, should guide area and handling planning.
Important variant qualification: Soundsulate’s broader line also sells 40-, 60- and 100-sq-ft rolls. A selector showing those sizes on a marketplace page is not proof that ASIN B0CN1G3C8Z supplies a 100-sq-ft pack. The original-ASIN-specific indexed seller descriptions independently state 32 sq ft. Even so, the exact option currently selected in Amazon checkout has not been inspected live, so check the 4 × 8-ft label before paying.
Disclosure: As an Amazon Associate I earn from qualifying purchases. The saved Soundsulate sponsored Amazon destination may earn a commission at no extra cost. TotalMass is linked to its distributor directly without creating an unverified Amazon affiliate route.
Soundsulate Next Generation 1 lb MLV — original 32 sq ft sheet

Soundsulate’s original-ASIN-specific retail listing identifies a 4-ft-wide by 8-ft-long material for 32 sq ft at about 1 lb per square foot and 0.12-in nominal thickness, typically rounded to 1/8 inch. Its approximate uncut material mass would be 32 × 1 = 32 lb, excluding packaging and added fasteners. A separate Soundsulate 4 × 8-ft retail record also aligns with the 32-sq-ft selection; do not infer that the manufacturer’s full product family always arrives in this format.
The material is described as flexible, dense PVC-based mass-loaded vinyl suitable as a barrier layer in selected wall or equipment installations. Its seller-advertised STC 27 must be read as a published material/test claim, not a prediction of the rating of an incomplete wall after simply adding a loose sheet. Installed sound-isolation performance also depends on sealing, flanking paths, penetrations, mass, mechanical bridging and all other assembly layers.
The original SPD Soundsulate product review uses the 4 × 8-ft 32-sq-ft version as its editorial reference. The unchanged original tracked destination is Soundsulate 1-lb MLV original 32-sq-ft ASIN — confirm selection. This is a saved active PADO product route, not live stock, shipping, price or a certified delivered package.
TotalMass 1 lb MLV — choose a 40- or 100-sq-ft roll

IsoStore’s TotalMass distributor specifications describe a 1 lb per sq ft, approximately 1/8-inch-thick black MLV barrier in 4 × 10-ft (40 sq ft) and 4 × 25-ft (100 sq ft) standard listings. The distributor also markets separate half-pound and two-pound TotalMass materials; these are not identical sheets or drop-in substitutions for 1-lb barrier when comparing acoustic assembly performance.
A 40-sq-ft, 1-lb product sheet represents roughly 40 lb of material before shipping, while a 100-sq-ft roll represents roughly 100 lb, consistent with nominal 1 lb/sq ft surface mass. Actual packed/shipping weights can exceed nominal material mass. The official distributor quotes STC 27 for the 1-lb version, but this does not establish that it or Soundsulate is universally quieter after installation; equivalence of test conditions is not independently confirmed here.
Read the SPD TotalMass MLV review for differences among the distributor’s half-, one- and two-pound sheets. The direct TotalMass distributor product page is an untracked buyer/source reference. This comparison originally had no saved TotalMass PADO Amazon product key, so no new tagged retailer destination or stock claim has been added.
Specification comparison
| Buyer point | Soundsulate original B0CN1G3C8Z | TotalMass 1 lb product family |
|---|---|---|
| Nominal area density | 1 lb/sq ft | 1 lb/sq ft |
| Nominal barrier thickness | About 0.12 in / approximately 1/8 in | About 1/8 in |
| Named pack format | 4 × 8 ft = 32 sq ft | 4 × 10 ft = 40 sq ft or 4 × 25 ft = 100 sq ft |
| Approximate product mass before package | 32 lb | 40 lb or 100 lb, based on selected size |
| Primary use | Flexible airborne-sound barrier layer | Flexible airborne-sound barrier layer |
| Claims about STC | Seller advertises 27 | Distributor lists 27 for 1-lb product |
| Original campaign affiliate | Amazon B0CN1G3C8Z | None; distributor direct |
| Identical assembly acoustic test | Not independently verified | Not independently verified |
The TotalMass 40-sq-ft option has nominally 40 ÷ 32 = 1.25 times the original Soundsulate area. The TotalMass 100-sq-ft roll has 100 ÷ 32 = 3.125 times that sheet area. Neither ratio is a gain in sound-transmission loss, acoustic ratings or installation quality. Calculate the barrier area your assembly needs, including proper overlaps, waste and the manufacturer’s approved joints.
Where these products fit—and where they do not
MLV is heavy, limp material whose mass helps limit some airborne sound paths when used in an appropriate sealed assembly. It is not a porous foam panel, carpet pad, door weather seal or a structural replacement for drywall, decoupling, insulation or penetrations detailing. It also cannot automatically stop footfall/impact vibration that travels through rigid connections.
For residential walls, design the complete sequence of framing, insulation, membrane, fastening, sealing and facing material. Avoid creating a rigid bridge that defeats decoupling. For ceilings, mass and attachment load are safety issues; never suspend an extremely heavy roll without structural and manufacturer guidance. For pipes and equipment, product compatibility, condensation, fire requirements and manufacturer installation method matter.
Buying and installation planning
Choose the 32-sq-ft Soundsulate selection when the job is a smaller measured barrier area, the 4 × 8-ft 1-lb MLV format can be handled safely, and the marketplace option is confirmed at checkout. Choose a TotalMass 40- or 100-sq-ft 1-lb roll when a larger system needs the distributor’s documented format and you have assessed material lifting, access and mounting.
Do not compare on manufacturer STC labels alone: a membrane’s reported rating is not the same as the STC of a completed room or partition. In any construction project, calculate loads and follow applicable assembly, electrical, moisture and fire requirements; do not substitute acoustical marketing for a tested wall design.
Frequently asked questions
Does Soundsulate ASIN B0CN1G3C8Z mean 100 sq ft?
The two independent original-ASIN-associated listings cited here describe 4 × 8 ft and 32 sq ft. Soundsulate sells 100-sq-ft family variants elsewhere, so verify the seller’s active selection rather than equating a family-size dropdown with this exact product key.
Does an STC 27 membrane make the completed wall STC 27?
No. Membrane ratings or seller test claims are not interchangeable with full wall or room assembly performance. Installed construction, flanking, sealing and coupling change the outcome.
Is TotalMass sold through an approved Amazon affiliate link here?
No. This original comparison only records an active Soundsulate PADO key; the TotalMass distributor page is direct and not a replacement affiliate product route.
Can either MLV eliminate floor impact noise?
Not reliably by itself. Airborne barriers do not replace impact decoupling, floor vibration control, resilient connections or proper structural design.
Source limitations and conclusion
Evidence includes an original Soundsulate-ASIN/32-sq-ft record, a matching-format seller record, IsoStore’s published TotalMass size and material specifications and the two SPD source reviews. A current live Amazon checkout selection, exact delivered variant, independent matched assembly sound test and TotalMass partner commission route have not been confirmed.
SPD’s conclusion: for comparable 1-lb MLV, select the exact verified size your assembly needs and install it as part of a complete sound-isolation design. No manufacturer STC snippet or nominal roll area proves an acoustic winner.
Good luck and happy soundproofing!